PROCESSING MODES SELECTION IN LOW-INTENSITY HYBRID MICROWAVE TECHNOLOGICAL COMPLEXES BASED ON "QUALITY-ENERGY CONSUMPTION" CRITERION

  • Геннадий Александрович Морозов Kazan National Research Techniсal University named after A.N.Tupolev
  • Юрий Евгеньевич Седельников Kazan National Research Techniсal University named after A.N.Tupolev
  • Владимир Иванович Анфиногентов Kazan National Research Techniсal University named after A.N.Tupolev http://orcid.org/0000-0003-0015-2429
  • Наталия Евгеньевна Стахова Kazan National Research Techniсal University named after A.N.Tupolev
  • Олег Геннадьевич Морозов Kazan National Research Techniсal University named after A.N.Tupolev http://orcid.org/0000-0003-4779-4656
Keywords: low-intensity hybrid microwave technological complex, microwave processing modes, idealized processing conditions, real conditions, optimal processing quality, “quality - energy consumption” ratio

Abstract

When creating a microwave technological complex (MWTC) of both unitary and hybrid types, the initial data for the designer are the data on the parameters of electromagnetic action. It is advisable to divide these parameters into two groups. The first of them refers to idealized processing conditions in a hypothetically homogeneous EMF (or, equivalently, EMF for an elementary volume of the processed material). The second group characterizes the processing parameters in real conditions, in particular, the heterogeneity of the EMF. The division into these groups is due to a number of reasons and also has the peculiarity that the first parameters are determined at the stage of pre-project studies, and the second parameters - at the stage of R&D. It should be emphasized that in most cases the stage of pre-project studies is carried out by specialists professionally oriented in the field of applications (biologists, chemists, etc.), while the R&D stage is carried out by radio engineers. This leads to the fact that the recommended processing conditions at best correspond to the conditions of optimal processing quality, i.e. they are determined without taking into account the specifics of subsequent implementation. The energy consumption factor and, especially, the reduced microwave energy costs often remain out of sight. We will call finding the specified parameters, optimal from the point of view of the “quality - energy consumption” ratio, determining the microwave processing mode. Examples and possibilities of effectively finding such modes corresponding to low-intensity MWTC for processing of seeds of agricultural and forest crops, inactivation of microorganisms and microflora, stimulating the development of bacteria and yeast, and processing of special polymers are considered in this paper.

Author Biographies

Геннадий Александрович Морозов, Kazan National Research Techniсal University named after A.N.Tupolev

Doctor of Technical Sciences, Professor, Professor of the Department of Radio Electronics and Microwave Technologies of the Kazan National Research Technical University named after A.N. Tupolev-KAI.

Research interests: microwave technologies.

Юрий Евгеньевич Седельников, Kazan National Research Techniсal University named after A.N.Tupolev

Doctor of Engineering Sciences, Professor, Professor of the Department of Radio Photonics and Microwave Technologies of KNITU-KAI named after A.N. Tupolev.

Research interests: amplitude distribution, antenna array, antenna array design, communication systems, electromagnetic waves, flat surface, high gain, leaky wave antenna, lens antenna, linear antenna, linear array, low side lobe level.

SPIN code: 4511-7480

Владимир Иванович Анфиногентов, Kazan National Research Techniсal University named after A.N.Tupolev

Doctor of Technical Sciences, graduated from Kazan State University named after V.I. Ulyanov-Lenin in 1973 in the specialty "Applied Mathematics", qualification - mathematician, works as an associate professor of the Department of Special Mathematics of Kazan National Research Technical University named after A.N. Tupolev-KAI.

Research interests: mathematical modeling of microwave processes and systems, microwave photonics. SPIN code: 1957-5220, AuthorID: 653438, WoS ResearcherID P-1741-2015, ScopusID: 14023946900.

E-mail: v.anfinogentov@yandex.ru

Наталия Евгеньевна Стахова, Kazan National Research Techniсal University named after A.N.Tupolev

Candidate of technical sciences, associate professor of the department of radio engineering systems KNITU-KAI named after N. Tupolev

Area of scientific interests: antenna array, electromagnetic waves, microwave technologies.

SPIN-code: 1255-8144

Олег Геннадьевич Морозов, Kazan National Research Techniсal University named after A.N.Tupolev

Doctor of Technical Sciences, Professor, Professor of the Department of Radiophotonics and Microwave Technology, KNRTU-KAI named after V.I. A.N. Tupolev Radio photonics, radio physics, applications in technical and living systems. SPIN-код: 4446-4570, AuthorID: 388026
ORCID https://orcid.org/0000-0003-4779-4656

ResearcherID: G-3896-2015
Scopus Author ID: 7006896538

Published
2025-08-04
Section
Electronics

Most read articles by the same author(s)

<< < 1 2 3 4 5 6